EN 10028-2 P265GH Flange
Werkstoff P265gh Blind Flanges Thickness Calculation For Pressure Vessel And Standard Specification Of P265Gh Steel Flange.

P265gh Flanges

Din En 10028-2 P265gh Flanges

Carbon Steel P265gh Blind Flange
Table Of Contents
- P265gh Flanges Non-alloy Quality Material?
- How Many Werkstoff P265gh Flange Temperature Ranges?
- En 10028-2 P265gh Used In The Oil And Gas Industry?
- En 10273 P265gh Flange Thickness Chart In MM
- P265gh Specification
- Carbon Steel P265gh Flange Weight Chart Table
- Welding Neck Flanges P265Gh Pressure Rating Table
- P265gh Tc1 Chemical Composition
- P265gh Mechanical Properties
- P265gh Blind Flanges Physical Properties
- P265gh En 10028 2 Equivalent
- Held Wide Stock Of Types Of P265gh Flange
What Is P265gh Material?
The material used in the manufacture of P265GH Flange is ideally well suited for use in between elevated temperature service to moderate temperatures. Since the Pressure Vessel Steel p265gh anchor flange is used for pressure purposes, the flange is commonly found in applications in industries such as the petrochemical, oil & gas, as well as the chemical industry. This European grade steel en 10028-2 p265gh standard flange has replaced the now obsolete BS1501 and DIN17155 specification.

P265gh Flanges Non-alloy Quality Material?
The p265gh tc2 flange is often considered to be a non-alloy quality material. Because the carbon steel grade p265gh tc1 flange has good weldable properties and is a pressure vessel and boiler steel grade material, it is used by the world's manufacturing fabricators. While the tensile strength of this carbon steel p265gh spacer blind flange ranges between 410 N/mm². to a max. of about 530 N/mm². At the standard thickness the minimum yield strength of these en 10216-2 p265gh forged flanges is about 265 MPa.
How Many Werkstoff P265gh Flange Temperature Ranges?
Due to the en 1092-2 Steel p265gh flange being weldable, in combination with its ability to withstand moderate to elevated temperatures, the flanges are often used in the manufacture for both steam boilers as well as pressurized vessel constructions. The p265gh en 10028-2 slip on flange is typically normalised by heating the material through the thickness of the flange to a temperature, which ranges between 890 °C to 950°C without the need for holding.
En 10028-2 P265gh Used In The Oil And Gas Industry?
Like majority of the products manufactured in our factory, this grade of p265gh tc2 threaded flange produced by us is typically subjected to a variety of stringent tests conducted on them before being distributed to our suppliers. Apart from being used in the oil and gas industry, its advantageous features as well as its cost effectiveness make the p265gh tc1 blind flange one of the most ideal flanges to be used in the used in chemical industry and pharmaceutical process plants.
En 10273 P265gh Flange Thickness Chart In MM
P265GH Flange Wall Thickness | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
NPS (Normal Pipe Sizes) | Outside Daimeter (O.D.) | Schedule 10 | Schedule 20 | Schedule 30 | STD Wall | Schedule 40 | Schedule 60 | EXT Hvy | Schedule 80 | Schedule 100 | Schedule 120 | Schedule 140 | Schedule 160 | XX Hvy |
½ | 0.84 | 0.083 | ... | ... | 0.109 | 0.109 | ... | 0.147 | 0.147 | ... | ... | ... | 0.188 | 0.294 |
¾ | 1.05 | 0.083 | ... | ... | 0.113 | 0.113 | ... | 0.154 | 0.154 | ... | ... | ... | 0.219 | 0.308 |
1 | 1.315 | 0.109 | ... | ... | 0.133 | 0.133 | ... | 0.179 | 0.179 | ... | ... | ... | 0.25 | 0.358 |
1 ¼ | 1.66 | 0.109 | ... | ... | 0.14 | 0.14 | ... | 0.191 | 0.191 | ... | ... | ... | 0.25 | 0.382 |
1 ½ | 1.9 | 0.109 | ... | ... | 0.145 | 0.145 | ... | 0.2 | 0.2 | ... | ... | ... | 0.281 | 0.4 |
2 | 2.375 | 0.109 | ... | ... | 0.154 | 0.154 | ... | 0.218 | 0.218 | ... | ... | ... | 0.344 | 0.436 |
2 ½ | 2.875 | 0.12 | ... | ... | 0.203 | 0.203 | ... | 0.276 | 0.276 | ... | ... | ... | 0.375 | 0.552 |
3 | 3.5 | 0.12 | ... | ... | 0.216 | 0.216 | ... | 0.3 | 0.3 | ... | ... | ... | 0.438 | 0.6 |
3 ½ | 4 | 0.12 | ... | ... | 0.226 | 0.226 | ... | 0.318 | 0.318 | ... | ... | ... | ... | 0.636 |
4 | 4.5 | 0.12 | ... | ... | 0.237 | 0.237 | ... | 0.337 | 0.337 | ... | 0.438 | ... | 0.531 | 0.674 |
5 | 5.563 | 0.134 | ... | ... | 0.258 | 0.258 | ... | 0.375 | 0.375 | ... | 0.5 | ... | 0.625 | 0.75 |
6 | 6.625 | 0.134 | ... | ... | 0.28 | 0.28 | ... | 0.432 | 0.432 | ... | 0.562 | ... | 0.719 | 0.864 |
8 | 8.625 | 0.148 | 0.25 | 0.277 | 0.322 | 0.322 | 0.406 | 0.5 | 0.5 | 0.594 | 0.719 | 0.812 | 0.906 | 0.875 |
10 | 10.75 | 0.165 | 0.25 | 0.307 | 0.365 | 0.365 | 0.5 | 0.5 | 0.594 | 0.719 | 0.844 | 1 | 1.125 | 1 |
12 | 12.75 | 0.18 | 0.25 | 0.33 | 0.375 | 0.406 | 0.562 | 0.5 | 0.688 | 0.844 | 1 | 1.125 | 1.312 | 1 |
14 | 14 | 0.25 | 0.312 | 0.375 | 0.375 | 0.438 | 0.594 | 0.5 | 0.75 | 0.938 | 1.094 | 1.25 | 1.406 | ... |
16 | 16 | 0.25 | 0.312 | 0.375 | 0.375 | 0.5 | 0.656 | 0.5 | 0.844 | 1.031 | 1.219 | 1.438 | 1.594 | ... |
18 | 18 | 0.25 | 0.312 | 0.438 | 0.375 | 0.562 | 0.75 | 0.5 | 0.938 | 1.156 | 1.375 | 1.562 | 1.781 | ... |
20 | 20 | 0.25 | 0.375 | 0.5 | 0.375 | 0.594 | 0.812 | 0.5 | 1.031 | 1.281 | 1.5 | 1.75 | 1.969 | ... |
22 | 22 | 0.25 | ... | ... | 0.375 | ... | ... | 0.5 | ... | ... | .... | .... | .... | .... |
24 | 24 | 0.25 | 0.375 | 0.562 | 0.375 | 0.688 | 0.969 | 0.5 | 1.219 | 1.531 | 1.812 | 2.062 | 2.344 | .... |
26 | 26 | .... | .... | .... | 0.375 | .... | .... | 0.5 | .... | .... | .... | .... | .... | .... |
30 | 30 | 0.312 | 0.5 | 0.625 | 0.375 | .... | .... | 0.5 | .... | .... | .... | .... | .... | .... |
36 | 36 | 0.312 | 0.5 | 0.625 | 0.375 | 0.75 | .... | 0.5 | .... | .... | .... | .... | .... | .... |
40 | 40 | .... | .... | .... | 0.375 | .... | .... | 0.5 | .... | .... | .... | .... | .... | .... |
42 | 42 | …….. | …….. | …….. | 0.375 | …….. | …….. | 0.5 | …….. | …….. | …….. | …….. | …….. | …….. |
48 | 48 | …….. | …….. | …….. | 0.375 | …….. | …….. | 0.5 | …….. | …….. | …….. | …….. | …….. | …….. |
P265gh Specification
Material Specification Of : | P265GH Flange |
---|---|
Common Types Of Flanges: | Slip On (SORF), Weld Neck (WNRF), Blind (BLRF), Lap Joint (Loose), Threaded (NPT), Socket-Weld (SWRF) |
Special Types Of Flanges : | Nipoflange, Elboflange, Latroflange, Swivel Flange, Expanding Flange, Reducing Flange, Weldoflange |
Marking Standard | Name of Manufacturer Schedule Type of Flange Facing Nominal Pipe Size Pressure Class ASME B16 Designation |
Bolt Type | high strength bolts medium strength bolts low strength bolts |
European Standard Flanges | JIS B2220 Flanges (5k to 30k) and KS1503 flanges |
Standard Cover : | pressure ratings & temperature ratings, materials, marking, dimensions, weight, tolerances, testing |
Contact Faces | RTJ (Ring Type Joint), FF (Flat Face), RF (Raised Face), T/G (Tongue And Groove ), M/F (Male And Female) |
Size Chart | Normal Pipe Size 1/2 to NPS 24" |
Thickness | Normal Pipe Size ≤ 18 |
Bore Diameter | Normal Pipe ≤ 10 |
Flanges Standards | EN 1092-1, JIS, ASME B16.5, ASME B16.47 type A, UNI, DIN |
Pressure Rating | Class 150 To Class 2500 |
High Temperature | Above 200°C (400°F) For Class 150 Or Above 400°C (750°F) |
Low Temperature | Above -29 Degree C (−20°F) |
Russian-Standard Flanges | GOST 12820 / 12821-80, DIN, UNI, EN 1092-1 |
South African Standard Flanges | SANSflanges And SABS flanges |
Surface Finish | smooth, concentric serrated, stock |
Gaskets Types | Full Face Gasket Flat Ring Gasket Metallic Ring Gakset |
Advantages Of Pipe Flange | Used to Connect Pipe System Easy Repair Pipe System Assembled Without Welding |
ISO Approved Carbon Steel P265gh Slip On Flanges Manufacturer In India And P265gh Plate Flange Weight Chart According to ASME B16.5.
Carbon Steel P265gh Flange Weight Chart Table
Nominal Pipe Sizes (NPS) | Slip On (SORF) | Threaded (NPT) | Socket Weld (SWRF) | Lap Joint (Loose) | Blind (BLRF) | Weld Neck (WRNR) |
---|---|---|---|---|---|---|
½ | 1 | 1 | 2 | 1 | 2 | 2 |
¾ | 2 | 2 | 2 | 2 | 2 | 2 |
1 | 2 | 2 | 2 | 2 | 2 | 3 |
1¼ | 3 | 3 | 3 | 3 | 3 | 3 |
1½ | 3 | 3 | 3 | 3 | 4 | 4 |
2 | 5 | 5 | 5 | 5 | 5 | 6 |
2½ | 8 | 8 | 8 | 8 | 7 | 10 |
3 | 9 | 9 | 9 | 9 | 9 | 11.5 |
3½ | 11 | 12 | 11 | 11 | 13 | 12 |
4 | 13 | 13 | 13 | 13 | 17 | 16.5 |
5 | 15 | 15 | 15 | 15 | 20 | 21 |
6 | 19 | 19 | 19 | 19 | 27 | 26 |
8 | 30 | 30 | 30 | 30 | 47 | 42 |
10 | 43 | 43 | 43 | 43 | 70 | 54 |
12 | 64 | 64 | 64 | 64 | 123 | 88 |
14 | 90 | 90 | 90 | 105 | 140 | 114 |
16 | 106 | 98 | 98 | 140 | 180 | 140 |
18 | 130 | 130 | 130 | 160 | 220 | 165 |
20 | 165 | 165 | 165 | 195 | 285 | 197 |
22 | 185 | 185 | 185 | 245 | 355 | 225 |
24 | 220 | 220 | 220 | 275 | 430 | 268 |
EN 10216-2 P265gh Weld Neck Flanges Pressure Rating Formula And P265gh Chemical Composition.
Welding Neck Flanges P265Gh Pressure Rating Table
P265GH Flange | Pressure Rating Chart | ||||||
Temperature °F | 150# | 300# | 400# | 600# | 900# | 1500# | 2500# |
-20 to 100 | 275 | 720 | 960 | 1440 | 2160 | 3600 | 6000 |
200 | 230 | 600 | 800 | 1200 | 1800 | 3000 | 5000 |
300 | 205 | 540 | 720 | 1080 | 1620 | 2700 | 4500 |
400 | 190 | 495 | 660 | 995 | 1490 | 2485 | 4140 |
500 | 170 | 465 | 620 | 930 | 1395 | 2330 | 3880 |
600 | 140 | 435 | 580 | 875 | 1310 | 2185 | 3640 |
650 | 125 | 430 | 575 | 860 | 1290 | 2150 | 3580 |
700 | 110 | 425 | 565 | 850 | 1275 | 2125 | 3540 |
750 | 95 | 415 | 555 | 830 | 1245 | 2075 | 3460 |
800 | 80 | 405 | 540 | 805 | 1210 | 2015 | 3360 |
850 | 65 | 395 | 530 | 790 | 1190 | 1980 | 3300 |
900 | 50 | 390 | 520 | 780 | 1165 | 1945 | 3240 |
950 | 35 | 380 | 510 | 765 | 1145 | 1910 | 3180 |
1000 | 20 | 320 | 430 | 640 | 965 | 1605 | 2675 |
1050 | 20 | 310 | 410 | 615 | 925 | 1545 | 2570 |
1100 | 20 | 255 | 345 | 515 | 770 | 1285 | 2145 |
1150 | 20 | 200 | 265 | 400 | 595 | 995 | 1655 |
1200 | 20 | 155 | 205 | 310 | 465 | 770 | 1285 |
1250 | 20 | 115 | 150 | 225 | 340 | 565 | 945 |
1300 | 20 | 85 | 115 | 170 | 255 | 430 | 715 |
1350 | 20 | 60 | 80 | 125 | 185 | 310 | 515 |
1400 | 20 | 50 | 65 | 95 | 145 | 240 | 400 |
1450 | 15 | 35 | 45 | 70 | 105 | 170 | 285 |
1500 | 10 | 25 | 35 | 55 | 80 | 135 | 230 |
P265gh Tc1 Chemical Composition
Element | % by mass | Element | % by mass |
Carbon (C) | ≤0.20 | Silicon (Si) | ≤0.40 |
Manganese (Mn) | 0.80 to 1.40 | Phosphorous (P) (maximum) | 0.025 |
Sulphur (S) (maximum) | 0.015 | Aluminium (Al) | <=0.020 |
Nitrogen (N) | <=0.012 | Chromium (Cr) | <=0.30 |
Copper (Cu) | <=0.30 | Molybdenum (Mo) | <=0.08 |
Niobium (Nb) | <=0.020 | Nickel (Ni) | <=0.30 |
Titanium (Ti) (maximum) | 0.03 | Vanadium (Vi) | <=0.02 |
P265gh Mechanical Properties
Nominal thickness (millimeter): | to 100 | 100 - 150 | 150 - 250 |
Rm - Tensile strength (MPa) (+N) | 410-530 | 400-530 | 390-530 |
Nominal thickness (millimeter): | to 16 | 16 - 40 | 40 - 60 | 60 - 100 | 100 - 150 | 150 - 250 |
ReH - Minimum yield strength (MPa) (+N) | 265 | 255 | 245 | 215 | 200 | 185 |
KV - Impact energy (J) transverse, (+N) | -20° 27 |
0° 27 |
+20° 40 |
KV - Impact energy (J) longitud., | -10° 28 |
0° 40 |
+20° 47 |
A - Min. elongation at fracture (%) (+N) | 22-23 |
A - Min. elongation at fracture (%) transverse, (+N) | 21 |
P265gh Blind Flanges Physical Properties
Temperature (°C) |
Modulus of elasticity (GPa) |
Mean coefficient of thermal expansion 10-6/(°C) between 20(°C) and | Thermal conductivity (W/m·°C) |
Specific thermal capacity (J/kg·°C) |
Specific electrical resistivity (Ω mm²/m) |
Density (kg/dm³) |
Poisson’s coefficient, ν |
---|---|---|---|---|---|---|---|
32 | - | - | 0.12 | - | |||
368 | 911 | - | 23.3 | 233 | - | ||
535 | - | 42 | 24.2 | 223 | 411 |
EN 10028-2 P265Gh Equivalent ASTM And Available Stock Of P265gh Pipe Flanges In India.
P265gh En 10028 2 Equivalent
EU EN |
USA - |
Germany DIN,WNr |
Japan JIS |
France AFNOR |
England BS |
Italy UNI |
Spain UNE |
Sweden SS |
Poland PN |
Czechia CSN |
Austria ONORM |
Russia GOST |
Inter ISO |
||||||||||||||||||||||||||||||
P265GH Flange |
|
|
|
|
|
|
|
|
|
|
|
|
|
Held Wide Stock Of Types Of P265gh Flange

P265gh En 10028-2 Threaded Flange

Werkstoff P265gh Socket Weld Flange

Carbon Steel P265gh Plate Flange

En 1092-1 Steel Grade P265gh Lap Joint Flange

Steel Grade P265gh Tc1 Blind Flange

Carbon Steel Grade P265gh Spectacle Blind Flanges

Carbon Steel Grade P265gh Tc1 Slip On Flange

P235gh Pressure Vessel Steel Weld Neck Flange

En 1.0345 Non-alloy Steel P235gh Raised Face Flanges
